No hay artículos en el carro
No hay artículos en el carroEste producto tiene pruebas de validación de resistencia para garantizar la mejor calidad y satisfacción. El diseño similar a OE garantiza la integridad estructural y el ajuste directo. Tiene un año de garantía limitada del producto. El diseño y el material superiores se aplican a componentes como juntas, pernos y pasadores para una mejor rigidez y una vida más larga. Es de zinc negro liso y hay una amplia selección en todas las marcas y modelos nacionales y extranjeros.
Kyle
Comentado en Canadá el 30 de mayo de 2019
Bolted right in place, good price, still works good, came on time
Anthony
Comentado en Canadá el 15 de marzo de 2019
Very happy with the handle I ordered, fit great and very good quality.Will order again if needed!
Lorena
Comentado en los Estados Unidos el 25 de julio de 2016
No more floppy handle for me! This handle fits perfectly and feels solid and strong. As others have mentioned, it is difficult to install. The bottom 10mm nut comes off easily because you can reach it through the access hole below the latching mechanism. The upper 10mm nut is harder to get to. Disconnecting the linkage rod from the key lock gives you enough room to put a wrench on the upper 10mm nut. I couldn't get a box end on it, so a stubby 10mm open end did the trick.
George Wang
Comentado en los Estados Unidos el 9 de septiembre de 2014
Fits and works just fine.Little hint for installation. Do not need to disconnect or remove the lock cylinder from key hole beneath the handle.Bottom 10mm mounting nut is easy to access, so fasten it first when installing. The 10mm nut on top is a whole new matter, may be difficult to thread it onto the bolt because its pretty much impossible to get two fingers in there (no pun). After a few failed attempts at that, I used a little bit of super glue to glue the nut onto one finger as was able to get it on the bolt, just don't use too much glue, as you'll need to pull your finger free afterwards. Hope this helps.Finally, on handles that feel like they are about to fail, try spraying WD40 inside the hinge of the handle. Will make the handle work like new again. I found out about this a little too late.
Chopper Rider
Comentado en los Estados Unidos el 11 de octubre de 2012
The handle works great after I replaced the plastic linkage snap with the one from the old handle. The new one was too big and never would have stayed in place. This installation was very hard and I had to figure out how every thing went in and worked without rubbing against the window track and door lock linkage parts. No videos or good information was available on the web that was helpful. You could not get an image with a camera or a video of this installation because everything was inside the door frame and hidden from view. You have to feel to find, remove and replace the two nuts ( I think they were 10mm) that hold the door handle on. I did do some grinding on the moving parts of this handle for extra clearance and used some good waterproof grease to lube the working parts. One thing I can tell ya is to make sure you put the working parts of the handle (from the outside) around and on the other side of the covered door lock linkage. This is not an easy task, but it can be done. You can get a peek through the plastic hole cover next to the door latch. I did loosen the latch by taking 3 star screws out for a little better view, but don't try to disengage any of the other door linkage. It is not necessary. After installation, It works smooth and easy. GOOD LUCK with your installation.Hollwood
Productos recomendados
Mex $1,001.69
Mex $ 520 .00 Mex $520.00
Mex $173.58
Mex $ 93 .00 Mex $93.00
Mex $438.33
Mex $ 197 .00 Mex $197.00
Mex $220.05
Mex $ 129 .00 Mex $129.00
Mex $589.07
Mex $ 300 .00 Mex $300.00
Mex $481.89
Mex $ 221 .00 Mex $221.00